EVGA P67 FTW Motherboard had huge success with the P55 FTW and it was painstaking one of the trailblazers in the aficionado planet. In our opinion it was really one the best boards of the P55 generation so we couldn’t wait to get out hands on the P67 version of the FTW. Even if EVGA experienced some major changes in the motherboard team and as a upshot they were late to the table with their P67 boards. This did allow them to avoid the Intel B2 P67 chipset recall failure but EVGA P67 FTW Motherboard new P67 were nonetheless delayed.Now over six months after the Intel’s P67 launch and several months after Z68 was first introduced, we finally have a P67 FTW in the lab. In the P67 planet the P67 FTW is a high-end board, competing with additional flagship products such as Gigabyte’s UD7, ASUS’ Maximus IV Extreme, and MSI’s Huge Bang Regulate. Part of what makes it such an appealing aficionado level board is the huge bundle of accessories it comes with and an NF200 chip which makes 3-way SLI doable. In terms of price the board we are reviewing (the K2 version) is accurate to $290 which is in the same range as the earlier mentioned competitor boards.
In terms of facial appearance and capabilities, the FTW is certainly up there with the huge boys. Even if, we’re sure many of you will be questioning this board’s placement in relation to the Z68 products that are unfilled from EVGA’s competitors. To us and many additional enthusiasts, the Z68’s advantages over its predecessor are a modest underwhelming which makes the P67 still relevant now. Users are still leaning towards the less high-priced choice as many don’t need the onboard record outputs and SSD caching offered by the newer chipset.
EVGA may be a bit late with this board but its long list of facial appearance and high performance pedigree should make it an appealing choice.
EVGA P67 FTW Motherboard Specifications and Facial appearance
Before jumping right into photos and hard, let’s take a look at the specifications for the P67 FTW.
For users looking for an NF200-based motherboard with point facial appearance or options we have produced a clever quick reference handbook that compares three of the top P67 boards, the P67 FTW, the M4E, and the UD7. Comparing the P67 FTW NF200 setup to Gigabyte’s P67 UD7 and ASUS’ M4E setups, each configuration is a bit uncommon:
- The P67 FTW has all PCI-E slots but one going through NF200
- The M4E bypasses NF200 when two cards are installed and then the NF200 is activated when three cards are installed
- The UD7 has all PCI-E slots always going through NF200
EVGA P67 FTW Motherboard may signal like a terrible business for a board to run SLI at 8x/8x but this will still go one better than 16x/16x SLI on P67 with NF200 in very near all suitcases. Only when you use a top level GPU and very high resolution (i.e. 2600 x 1600) will 16x/16x NF200 come out on top. The reason the UD7 is able to run 16x SLI for dual card is because the NF200 takes the native 8 lane 5GT/s bus, splits the PCIE lanes and doubles the bandwidth to 16x5GT/s. This allows for 32 lanes of 2.5GT/S PCIE or dual 16x.
The box of the EVGA P67 FTW Motherboard uses a akin design to the P55 FTW with a black color machinate and grey calligraphy albeit with a upset of red added. This change is because the FTW has full the Classified’s house as EVGA’s flagship board and thus the FTW now uses the Classified color machinate.
On one side of the box EVGA lists the accessories built-in in the box and on the contrary side there is a modest enter-up on how EVGA is #1 in a digit of areas.
Typical to most contemporary motherboards, the P67 FTW’s box has a not glossy black interior composed of thin cardboard. EVGA P67 FTW Motherboard is likely to grant flexibility and cut down on print expenditure. Having a look inside there is a mountain of accessories, each in EVGA P67 FTW Motherboard own anti-static bag.
EVGA P67 FTW Motherboard
Beneath a cardboard partition is the motherboard itself which is wrapped in an anti-static bag. Meanwhile, as you can see the belt pile really is fantastic.
Privileged than is a list of accessories built-in with the board and their associated descriptions.
Compelling a closer look at a few accessories, we have three SLI bridges that come with the board: a flex bridge for dual SLI, and two bridges of uncommon lengths for tri-SLI. In view of the fact that there are a digit of PCI-E slots unfilled to run your record cards, EVGA P67 FTW Motherboard has accounted for all configurations. Next up are USB 2.0 and USB 3.0 brackets for superfluous peripheral USB ports.
The EVGA P67 FTW Motherboard and ECP Panel are two optional accessories that only come with the K2 version of the FTW or can be bought unconnectedly supervise over from EVGA P67 FTW Motherboard. EVGauge is a timer speed gauge that dynamically shows the logic’s timer speed even as the ECP Panel gives users the skill to boost vCore and VCCSA, clear CMOS, and disable/enable PCI-E slots with a push of a pin. The ECP Panel also has the debug LED to show CPU temps and debug post on the front of your PC.
Although we did delight in the extras in the bundle we did find a few issues with some of the accessories. First of all, there is no indication on the SATA cables to top toward which are SATA2 and which are SATA3. For whatever reason, the EVGauge cable is also very fleeting so placement options become quite restricted.
One of the more glaring issues we encountered was the ECP Panel’s lack of built-in screws in view of the fact that the ones required are less vital than normal. This means users would have to go to a hardware store and buy 2.5mm screws or contact EVGA to get some shipped. In their defense, EVGA P67 FTW Motherboard has said that upcoming shipments of the FTW K2 will contain the necessary screws.
No comments:
Post a Comment